SPECIFICATIONS
BS 4254 ; BS 5212 ; ASTM C 920
DESCRIPTION
Perma Polyseal is a two part polysulphide sealant based on polysulphide resin, curing agents, select fillers, plasticisers and vulcanising agents. When the base and curing agent are mixed it forms an uniform colour mass which can either be poured in to the horizontal expansion joints or gunned into the vertical joint depending upon the grade. Essentially Perma Polyseal is available in two grades. Pouring grade for horizontal application and gun grade for non slump vertical applications
PRIMARY USES
Perma Polyseal is an expansion joint sealant useful in sealing horizontal as well as vertical joints. Perma Polyseal is used for sealing reappearing cracks on the roofs, shear cracks in the brickworks and joints in water tanks. Perma Polyseal is used for sealing gaps between the building material of different structures such as concrete and wood, glass and aluminium, and exterior glazings. Perma Poly seal is used in expansion joints varying between 6mm to 50 mm.
ADVANTAGES
1. Perma Polyseal seals the joints and makes them watertight.
2. Perma Polyseal accomodates the movement of structures because of expansion contraction and also because of deflections and settlements.
3. Perma Polyseal is tough hence floor joints treated with Polysulphide can be trafficable.
4. Peram Polyseal when dry gives an aesthetic smooth grey appearance.
5. Perma Polyseal is resistant to chemical spillages and also resistant to Oils, Petrol, Diesel and Solve- nts.
DIRECTION FOR USE
1) SURFACE PREPARATION :
All joints to be sealed with Perma Polyseal should be dry clean and free from any dirt, dust, rust, scale or any protective lacquer or grease. Expansion joint fill material (bitumen impregnated board) shall be tightly packed in position so that a clear joint depth as per joint design is available. As a thumb rule depth of joint is taken as half its width and the depth is not less than 6mm. A bond-breaking tape or cellow tape is fixed on the joint fill board to avoid direct contact between Perma Polyseal and the Board. Apply masking tape on top surface on either side of the joint to avoid staining of neighbouring area.
2) PRIMING :
If the sides of the joints are porous and irregular use Polysulphide primer which is a two component material. Mix the two components and brush apply on the sides of the joint. When the primer becomes tack free apply or pour Perma Polyseal in the joint.
3) MIXING :
Transfer the entire contents of the small curing agent pack to the larger pack of the base and mix thoroughly for five minutes by electric drill with blades or manually till a uniform consistency paste is obtained.
4) APPLICATION :
Pour the mixed Perma Polyseal in the joints and finish the joints using rounded spatula or similar object to bring about a smooth surface and also remove any air which might have got entrapped during mixing. It is advisable to finish the surface slightly concave to keep the Perma Polyseal unaffected by heavy trolley movements.
COVERAGE CHART
Coverage or the length of the joint sealed with one kg of Poly sulphide depends on the width. The following table gives the coverage in meter per kg of Poly sulphide for various joint thicknesses.
DEPTH |
WIDTH OF JOINT IN mm |
|||||||||
6mm |
10mm |
15mm |
20mm |
25mm |
30mm |
35mm |
40mm |
45mm |
50mm |
|
6mm |
17.90 |
10.75 |
7.16 |
|||||||
10mm |
4.30 |
3.22 |
2.58 |
|||||||
15mm |
2.15 |
1.72 |
1.43 |
|||||||
20mm |
1.29 |
1.07 |
0.92 |
0.81 |
0.72 |
|||||
25mm |
0.74 |
0.65 |
0.57 |
0.52 |
CHEMICAL RESISTANCE
Chemical resistance of Perma Polyseal against
various chemicals is as follows:-
Dilutands |
- Resistant |
Dilute alkalis |
- Resistant |
Petrol |
- Resistant |
Aviation fuels |
- Resistant |
Diesel |
- Resistant |
Kerosene |
- Resistant |
Lubricating Oil |
- Resistant |
White Spirit |
- Resistant |
Chlorinated solvents |
- Not Resistant |
Aromatic Solvents |
- Not Resistant |
Dilute Oxidising Aids |
- Not Resistant |
PACKING
Perma Polyseal is available in 1kg & 4kg packings
SHELF LIFE
Twelve months if stored in manufacturer’s original
packing.
QUALITY ASSURANCE
All “PERMA” branded products are manufactured under strict quality control supervision as per exact manufacturing specification. Should you find the behaviour of the product varying from the claims in the data sheets please stop the use of the product and contact the nearest Perma staff or distributor.
STATEMENT OF RESPONSIBILITY
Perma branded products when used in accordance with its current published directions for use performs as per its data sheets / catalogue. The manufacturer and the distributor will not be responsible for other materials and conditions of inferior workmanship.